frostschutz schriebWas sagt denn smartctl -a zu der Festplatte?
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-5.4.5-arch1-1] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.D
Device Model: Hitachi HDS721010DLE630
Serial Number: MSE523RP006ZNH
LU WWN Device Id: 5 000cca 37fc01a3c
Firmware Version: MS2OA610
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Dec 29 16:25:19 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 7507) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 126) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 085 085 016 Pre-fail Always - 4391071
2 Throughput_Performance 0x0005 140 140 054 Pre-fail Offline - 77
3 Spin_Up_Time 0x0007 108 108 024 Pre-fail Always - 211 (Average 212)
4 Start_Stop_Count 0x0012 097 097 000 Old_age Always - 12824
5 Reallocated_Sector_Ct 0x0033 091 091 005 Pre-fail Always - 325
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 118 118 020 Pre-fail Offline - 33
9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 24253
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 4167
192 Power-Off_Retract_Count 0x0032 090 090 000 Old_age Always - 12825
193 Load_Cycle_Count 0x0012 090 090 000 Old_age Always - 12825
194 Temperature_Celsius 0x0002 206 206 000 Old_age Always - 29 (Min/Max 14/48)
196 Reallocated_Event_Count 0x0032 091 091 000 Old_age Always - 334
197 Current_Pending_Sector 0x0022 095 095 000 Old_age Always - 280
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 3933 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3933 occurred at disk power-on lifetime: 24252 hours (1010 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 90 70 0a 40 05 Error: UNC at LBA = 0x05400a70 = 88083056
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 38 98 09 01 40 00 00:00:49.322 READ FPDMA QUEUED
60 f8 b8 08 0a 40 40 00 00:00:49.302 READ FPDMA QUEUED
60 08 b0 68 18 01 40 00 00:00:49.292 READ FPDMA QUEUED
60 08 30 a0 1d c6 40 00 00:00:49.195 READ FPDMA QUEUED
60 08 28 98 1d c6 40 00 00:00:49.194 READ FPDMA QUEUED
Error 3932 occurred at disk power-on lifetime: 24252 hours (1010 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 40 c0 0b 40 05 Error: UNC at LBA = 0x05400bc0 = 88083392
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 b0 10 1d 53 40 00 00:00:35.647 READ FPDMA QUEUED
60 08 a8 38 28 04 40 00 00:00:35.647 READ FPDMA QUEUED
60 08 a0 10 08 04 40 00 00:00:35.647 READ FPDMA QUEUED
60 00 80 00 5e 04 40 00 00:00:35.647 READ FPDMA QUEUED
60 08 70 d0 76 81 40 00 00:00:35.647 READ FPDMA QUEUED
Error 3931 occurred at disk power-on lifetime: 24252 hours (1010 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 a0 0b 40 05 Error: UNC at LBA = 0x05400ba0 = 88083360
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 48 00 5d 04 40 00 00:00:31.762 READ FPDMA QUEUED
60 00 40 00 5c 04 40 00 00:00:31.761 READ FPDMA QUEUED
60 08 d8 08 c8 21 40 00 00:00:31.760 READ FPDMA QUEUED
60 00 38 00 5b 04 40 00 00:00:31.758 READ FPDMA QUEUED
60 40 30 c0 0b 40 40 00 00:00:31.754 READ FPDMA QUEUED
Error 3930 occurred at disk power-on lifetime: 24252 hours (1010 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 48 c0 0b 40 05 Error: UNC at LBA = 0x05400bc0 = 88083392
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 78 28 08 04 40 00 00:00:27.603 READ FPDMA QUEUED
60 08 70 08 08 00 40 00 00:00:27.591 READ FPDMA QUEUED
60 08 68 e0 28 cd 40 00 00:00:27.581 READ FPDMA QUEUED
60 08 60 00 33 01 40 00 00:00:27.549 READ FPDMA QUEUED
60 08 40 58 ef 04 40 00 00:00:27.548 READ FPDMA QUEUED
Error 3929 occurred at disk power-on lifetime: 24252 hours (1010 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 68 a0 0b 40 05 Error: WP at LBA = 0x05400ba0 = 88083360
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 28 00 09 01 40 00 00:00:23.578 WRITE FPDMA QUEUED
61 08 20 10 1a 00 40 00 00:00:23.578 WRITE FPDMA QUEUED
61 08 18 00 09 00 40 00 00:00:23.578 WRITE FPDMA QUEUED
61 08 10 88 08 00 40 00 00:00:23.578 WRITE FPDMA QUEUED
61 08 08 a0 0b 00 40 00 00:00:23.578 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
frostschutz schrieb
Machst du irgendwas mit Hibernate / Suspend to Disk?
Ziehst du einfach so den Stecker statt die Kiste richtig runterzufahren?
Irgendwas im dmesg oder anderen Logs wenn das passiert?
Ich verwende kein Hibernate o.ä. und Fahre den Rechner immer ordnungsgemäß herrunter. Was dmesg angeht habe ich nichts auffälliges gefunden. Ich vermute dass der Fehler beim booten auftritt, weis aber nicht worauf ich achten soll.
frostschutz schriebDeine fsck Optionen sind ziemlich brutal (force, yes-all, ...) und falsch angewendet macht man mit fsck gerne auch mal mehr kaputt als ganz. In jedem Fall solltest du ein Backup von dem machen was noch da ist...
Die daten Sind gottseidank alls Backup extern gesichert
(ansonsten hätte ich fsck garnicht verwendet da ich nur wenig erfahrung damit habe). Das oben beschriebene fsck Kommando hat diese Fehler bis vor kurzem beheben können, hat jetzt aber keinen sichtbaren Effekt mehr
(auch keinen negativen).