Hallo Zusammen,
ich habe die letzen Tage versucht, eine neue Festplatte ins System einzubinden. Nachdem ich zuerst den ebenfalls neuen Sharkoon SATA-Quickport vreflucht habe, habe ich die Festplatte direkt intern eingebaut und bin auch kläglich gescheitert.
Nun bin ich mal auf die Idee gekommen, die S.M.A.R.T.-Werte auszulesen:
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.9.10-1-ck-haswell] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Blue
Device Model: WDC WD30EZRZ-00Z5HB0
Serial Number: WD-WCC4N5JHPAFD
LU WWN Device Id: 5 0014ee 20e0430a5
Firmware Version: 80.00A80
User Capacity: 3.000.592.982.016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Feb 19 11:03:27 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (38940) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 391) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 219 181 021 Pre-fail Always - 4016
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 29
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 1967
7 Seek_Error_Rate 0x002e 001 001 000 Old_age Always - 65535
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 70
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 22
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 17
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 57
194 Temperature_Celsius 0x0022 119 109 000 Old_age Always - 31
196 Reallocated_Event_Count 0x0032 192 192 000 Old_age Always - 8
197 Current_Pending_Sector 0x0032 066 066 000 Old_age Always - 65524
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Ich denke mal die ID 5 mit "FAILING NOW" sollte mir sorgen machen, ich habe aber keine Ahnung, wie ich die Werte interpretieren soll. Kann ich erkennen, ob die wahrscheinlichste Fehlerursache die Platte, das SATA-Kabel oder die Stromversorgung ist? Oder hilft nur Trial-And-Error?
Viele Grüße,
Jürgen