SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 199 199 051 Pre-fail Always - 21207
3 Spin_Up_Time 0x0027 177 174 021 Pre-fail Always - 2150
4 Start_Stop_Count 0x0032 092 092 000 Old_age Always - 8382
5 Reallocated_Sector_Ct 0x0033 188 188 140 Pre-fail Always - 106
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 8096
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 094 094 000 Old_age Always - 6032
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 2657
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 209
193 Load_Cycle_Count 0x0032 154 154 000 Old_age Always - 138959
194 Temperature_Celsius 0x0022 119 101 000 Old_age Always - 28
196 Reallocated_Event_Count 0x0032 199 118 000 Old_age Always - 1
197 Current_Pending_Sector 0x0032 197 001 000 Old_age Always - 467
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
Bei einer ca. 6 Jahre alten Festplatte habe ich massive Leseprobleme, Zu Beginn konnte ich kein backup mehr erstellen (Windows 7), Nach chkdsk /r /f liess sich die Platte, auch eingebaut in einen anderen Rechner, überhaupt nicht mehr starten, Die Erkennung als sata-Platte misslang. Hier
badblocks -f -t 0 -v -e 1000000 -b 4096 -s -w /dev/sdb
Nach defekten Blöcken wird gesucht (Lesen+Schreiben-Modus)
Von Block 0 bis 183143645
Mit Muster 0x wird getestet00: 0.00% erledigt, 0:00 verstrichen. (0/0/0 Fehler^C 1.07% erledigt, 1:26:02 verstrichen. (0/0/0 Fehler)
Interrupted at block 1952192
root@miyolinux:/home/userxy# mke2fs -b 4096 -v /dev/sdb
mke2fs 1.42.12 (29-Aug-2014)
Dateisystemtypen für das Aufschlüsseln von mke2fs.conf: 'ext2'
Dateisystembezeichnung=
OS-Typ: Linux
Blockgröße=4096 (log=2)
Fragmentgröße=4096 (log=2)
Stride=0 Blöcke, Stripebreite=0 Blöcke
45793280 Inodes, 183143646 Blöcke
9157182 Blöcke (5.00%) reserviert für den Superuser
Erster Datenblock=0
Maximale Dateisystem-Blöcke=4294967296
5590 Blockgruppen
32768 Blöcke pro Gruppe, 32768 Fragmente pro Gruppe
8192 Inodes pro Gruppe
UUID des Dateisystems: 3c30cbc7-c34c-48cf-a510-744b419cd677
Superblock-Sicherungskopien gespeichert in den Blöcken:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968,
102400000
beim Anfordern von Speicher für die Gruppentabellen: erledigt
Inode-Tabellen werden geschrieben: erledigt
ext2fs_mkdir: Der Versuch, einen Block vom Dateisystem zu lesen, endete in kurzem Lesen beim Erstellen des Wurzelverzeichnisses
root@miyolinux:/home/userxy# cfdisk /dev/sdb
cfdisk: cannot open /dev/sdb: Eingabe-/Ausgabefehler
root@miyolinux:/home/userxy# smartctl -t short /dev/sdb
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Short self-test routine immediately in off-line mode".
Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 2 minutes for test to complete.
Test will complete after Fri Feb 17 08:02:38 2017
Use smartctl -X to abort test.
root@miyolinux:/home/userxy# smartctl -a /dev/sdb
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-3.16.0-4-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA (AF)
Device Model: WDC WD7500BPVT-22HXZT3
Serial Number: WD-WXL1E61NDFF3
LU WWN Device Id: 5 0014ee 656ccbe3a
Firmware Version: 01.01A01
User Capacity: 750'156'374'016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Feb 17 08:07:48 2017 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 248) Self-test routine in progress...
80% of test remaining.
Total time to complete Offline
data collection: (17160) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 169) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 199 199 051 Pre-fail Always - 21207
3 Spin_Up_Time 0x0027 177 174 021 Pre-fail Always - 2150
4 Start_Stop_Count 0x0032 092 092 000 Old_age Always - 8382
5 Reallocated_Sector_Ct 0x0033 188 188 140 Pre-fail Always - 106
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 8096
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 094 094 000 Old_age Always - 6032
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 2657
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 209
193 Load_Cycle_Count 0x0032 154 154 000 Old_age Always - 138959
194 Temperature_Celsius 0x0022 119 101 000 Old_age Always - 28
196 Reallocated_Event_Count 0x0032 199 118 000 Old_age Always - 1
197 Current_Pending_Sector 0x0032 197 001 000 Old_age Always - 467
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 161 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 161 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:20.619 READ DMA
ec 00 00 00 00 00 a0 08 00:04:20.610 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:04:20.602 SET FEATURES [Set transfer mode]
Error 160 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:04.964 READ DMA
ec 00 01 00 00 00 00 08 00:03:54.057 IDENTIFY DEVICE
Error 159 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:03:44.370 READ DMA
ec 00 00 00 00 00 a0 08 00:03:44.361 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:03:44.354 SET FEATURES [Set transfer mode]
Error 158 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:03:40.465 READ DMA
ec 00 01 00 00 00 00 08 00:03:38.984 IDENTIFY DEVICE
Error 157 occurred at disk power-on lifetime: 8086 hours (336 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
01 51 08 00 00 00 e0 Error: AMNF 8 sectors at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:03:34.459 READ DMA
ec 00 00 00 00 00 a0 08 00:03:34.450 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:03:34.443 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 8085 57353089
# 2 Short offline Completed: read failure 90% 8085 57353089
# 3 Short offline Completed: read failure 90% 8084 57353088
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
nun die Schritte, die ich unternommen habe, damit die bad sectors wieder werden können. Denke aber, die Platte ist hinüber, aufgrund der hohen raw-value Werte bei 1, 5, 191 und 197. Den badblocks Befehl habe ich abgebrochen, da ich mich nicht tagelang (1.07% in 1:26:02) auf das Resultat warten konnte und weil es sich - wahrscheinlich (?) nicht rentiert. Das WD Programm ist beim Kurztest abgestürzt. Das HP Bios HD checkprogramm hat gemeldet, die Platte müsse ersetzt werden, aber so schnell möchte ich nicht aufgeben. Falls die Wahrscheinlichkeit > 50% ist, dass die Platte noch ein paar Jährchen laufen kann, würde ich einen laptop auch ein paar Tage lang sich damit befassen lassen (die Platte war über usb-sata Adapter angeschlossen, daher sdb).