Hi,
ich bin heute auf ein Problem gestoßen, welches ich so noch nie hatte. Der Rechner erkennt meine WLAN-Karte nicht. Selbst ein "ls /sys/class/net/" bringt mir nur die Schnittstellen "eth0 irda0 lo".
Ein "dmesg | grep -i ipw2200" wirft mir folgendes raus:
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ipw2200: Detected Intel PRO/Wireless 2915ABG Network Connection
firmware: requesting ipw2200-bss.fw
ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2
ipw2200: Unable to load firmware: -2
ipw2200: failed to register network device
ipw2200: probe of 0000:02:02.0 failed with error -5
Das Paket ipw2200-fw ist aber installiert. "ls /lib/firmware" bestätigt dies auch:
LICENSE.ipw2200-fw ipw2200-bss.fw ipw2200-ibss.fw ipw2200-sniffer.fw
Ich habe eth1 in die /etc/rc.conf eingetragen. In der /etc/mkinitcpio.conf habe ich unter HOOKS "firmware" eingetragen. Dennoch wird die Firmware nicht geladen.
Wie kann ich dieses Problem beheben?
Gruß
Benny
Edit:
Mit dem Befehl:
rmmod ipw2200 && modprobe ipw2200
geht die Karte wunderbar. Zum besseren Verständis hier meine rc.conf und mkinitcpio.conf:
rc.conf
#
# /etc/rc.conf - Main Configuration for Arch Linux
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="de_DE.utf8"
HARDWARECLOCK="localtime"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="de-latin1-nodeadkeys"
CONSOLEFONT="lat9w-16"
CONSOLEMAP=
USECOLOR="yes"
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
#
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
#
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(e1000 slhc ipw2200 ac97_bus snd-mixer-oss snd-pcm-oss snd-page-alloc snd-pcm snd-timer snd snd-ac97-codec snd-intel8x0 snd-intel8x0m soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="odin"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
#
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#
eth0="dhcp"
eth1="dhcp"
INTERFACES=(lo !eth0 !eth1)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="dhcp"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(@syslog-ng !hotplug !pcmcia !network dbus hal netfs !crond acpid alsa dhcdbd networkmanager portmap fam)
mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES="pata_acpi ata_generic scsi_mod ata_piix"
# BINARIES
# This setting includes, into the CPIO image, and additional
# binaries a given user may wish. This is run first, so may
# be used to override the actual binaries used in a given hook.
# (Existing files are NOT overwritten is already added)
# BINARIES are dependancy parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in anyway. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options,
# like so:
# FILES="/etc/modprobe.conf"
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'modload' may be used in place of 'udev', but is not recommended
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
# This setup specifies all modules in the MODULES setting above.
# No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
#
# This setup will autodetect all modules for your system and should
# work as a sane default
# HOOKS="base udev autodetect pata scsi sata filesystems"
#
# This is identical to the above, except the old ide subsystem is
# used for IDE devices instead of the new pata subsystem.
# HOOKS="base udev autodetect ide scsi sata filesystems"
#
# This setup will generate a 'full' image which supports most systems.
# No autodetection is done.
# HOOKS="base udev pata scsi sata usb filesystems"
#
# This setup assembles an pata raid array with an encrypted root FS.
# Note: See 'mkinitcpio -H raid' for more information on raid devices.
# HOOKS="base udev pata raid encrypt filesystems"
#
# This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev fw autodetect firmware pata scsi sata usb net keymap filesystems"